Re: MX64 and Vonage (not compatible accoding to Vonage)
Is it the vonage box or just vonage desk phones?
View ArticleRe: Congratulations to the September 2018 Meraki Community Members of the Month
Glad we could make it easy on you this month 😉
View ArticleRe: MX64 and Vonage (not compatible accoding to Vonage)
You could try 1:1 NAT a phone to basically eliminate the MX as a variable and see if it makes a difference.
View ArticleRe: MX WAN connected to a load balancer
I've never tested this but my guess is the VPN tunnel would establish through one of the WAN links and hold its session open there.
View ArticleRe: MS250 Fiber SFP+
Also it looks like that SFP is designed for multi mode fiber. Are you sure that is what is running between your MDF and IDF? Is it possibly single mode?
View ArticleRe: MX68 not arping Cisco switch
Your best bet for this type of config is to setup the switch port going to the router as access vlan X. Use a VLAN you don't use for other stuff. Then setup the port going to the MX as access with...
View ArticleGood/Bad News
I got a new job in a non Meraki environment so I probably won't be here as much as I usually am. I still do consulting on the side and I primarily recommend Meraki equipment so I won't be a complete...
View ArticleRe: Suggestions for Wall Mounting MS120-24/48
We use the 4U version of what @BlakeRichardson recommended.
View ArticleDisney Circle
Has anyone configured a Disney Circle device to work with an MX? I guess the device uses ARP Spoofing/Poisoning re: https://support.meetcircle.com/hc/en-us/articles/115001381932-How-Does-Circle-Work-...
View ArticleRe: Disney Circle
I'll be testing it in the near future so I'll report the results. I like the idea/ability of the Disney Circle to make managing access time easy. But strange implementation.
View ArticleRe: Disney Circle
@jdsilva, the circle makes it very easy for the average home user to manage dynamic policies. If you take a pass through this https://cdn.meetcircle.com/support-files/User+Manual+-+Circle.pdf you can...
View ArticleRe: MX for Gigabit Internet
MX67 only supports max throughput of 300M with all security enabled. The first device that can support 1G internet is the MX250 which is way to expensive for a small site. This is still painful for...
View ArticleRe: Disney Circle
I plugged it directly into the MX but that port was setup on the same vlan as the wireless. Worked as intended, no issues.
View ArticleRe: MX for Gigabit Internet
I only have MX64 and MX65 networks so I'm not sure. The number I provided is based off of this (see page 3) https://meraki.cisco.com/lib/pdf/meraki_whitepaper_mx_sizing_guide.pdf Which is pretty...
View ArticleRe: MX for Gigabit Internet
I've run speedtests at sites MX64 and 1G burstable circuits and had the 250M limit.
View ArticleRe: MX Configuration
What are you trying to accomplish? In most setups the same LAN shares the two WANs load balanced. You can set an internet preference if something LAN side needs to stick to a certain LAN interface.
View ArticleRe: MS220-48LP device uptime
Bumping an old thread, I am surprised to see this information is still not exposed in the dashboard. Had a power event at one of our sites and was trying to verify if the Meraki equipment power...
View ArticleBLE BLEEDINGBIT
I couldn’t find anything in the wireless section on this issue. Here is some information and resources....
View ArticleRe: BLE BLEEDINGBIT
Interesting, didn't see anything directly related in the 25.13 firmware notes. The closest thing I see is thisFixed an issue where the BLE radio would stop beaconing and scanning (MR30H/MR33/MR74)
View Article
More Pages to Explore .....